Menu Close

Kode Error Canon IRAdvance 4535

|| 5 Comments
Kode Error Canon IRAdvance 4535

Kode Error Canon IRAdvance

Kode Error Canon IRAdvance 4535

Tips dibawah ini cara mengatasi masalah pada mesin fotocopy Canon IRAdvance 4525i/ 4535i/ 4545i/ 4551i agar anda mudah mengidentifikasi kesalahan serta memperbaiki dengan cepat.

Daftar Isi :

Kode Error Canon IRAdvance 4535, 4035, 4245, 4251

  • Fixing temperature abnormal rise, Penyebab dari Suhu yang terdeteksi oleh termistor utama tidak naik ke nilai yang ditentukan selama kontrol start-up.

    • Perbaiki: Bagian Harness yang menghubungkan dari DC Controller PCB (UN2/J307) ke Fixing Main Thermistor (TH1/ J707). Cek Fixing Main Thermistor (TH1) pada Fixing Unit dan DC Controller PCB.

    • Lakukan yang berikut untuk menghapus kesalahan: COPIER> FUNCTION> CLEAR> ERR; dan kemudian MATIKAN dan AKTIFKAN daya.

    • Periksa/ganti harness dan konektor antara DC Controller PCB dan Fixing Main Thermistor.
    • Ganti Termistor Utama (Unit Film).
    • Ganti PCB Pengontrol DC. ( Sebelum mengganti PCB Kontroler, cadangkan data mode layanan dan pulihkan data cadangan setelah penggantian agar data dapat dilindungi/ Backup ) dengan cara : COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Untuk Restor : COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
  • Fixing unit temperature rise detection :

    Penyebab : Pembacaan sub termistor adalah 295 derajat C atau lebih terus menerus selama 200 msec.

    Pembacaan termistor utama kurang dari 115 derajat C terus menerus selama 400 msec 2,5 detik setelah itu menunjukkan 100 derajat C. 2.Pembacaan termistor utama kurang dari 150 derajat C terus menerus selama 400 msec 1,3 detik setelahnya telah menunjukkan 140 derajat .

    Perbaikan : ganti Therminstor Unit

  • Developing Toner Sensor is disconnected :

    • Penyebab : Sensor Toner “ON” setiap 2,5 detik sensor menyala. Level Toner tidak bertambah dalam 1 hitungan setiap 15 kali saat sensor menyala.

    • Perbaikan : Developing Assembly Toner Sensor, Replace. Check/replace the related harness/cable, connector and parts.

Kode Error Canon IRAdvance 6055, 6075, 6265, 6275

Description : Fixing Assembly low temperature error
Temperature of the Fixing Main Thermistor (THM1) does not reach 70 degC although 20 seconds have passed after starting the Fixing Roller temperature control.

Remedy :

  1. Check the connection of the Fixing Assembly. (Connection error of the Drawer, connector disconnection, open circuit) -> Replace the Heater Assembly.
  2. Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10) (connector disconnection, open circuit, the caught cable).
  3. Replace the Fixing Power Supply PCB (PCB10). 4. Replace the Main Driver PCB (PCB2). 5. Replace the DC Controller PCB (PCB1).
  • E000-0002 : Fixing Assembly low temperature error
    Temperature of the Fixing Main Thermistor (THM1) does not reach 10 degC although 20 seconds have passed after starting the Fixing Roller temperature control.
  • E001-0002 : Fixing Assembly high temperature error (software detection)
    • The Fixing Main Thermistor (THM1) detects 230 degC or higher.
    • The Fixing Sub Thermistor 1 (THM2)/Fixing Sub Thermistor 2 (THM3) detects 230 degC or higher for 2 consecutive seconds.
  • E002-0001 :
    • Check the connection of the Fixing Main Thermistor (THM1). : Replace the Fixing Main Thermistor Unit
    • Replace the Fixing Power Supply PCB (PCB10)
  • E004-0010 :
    • Fixing Power Supply error
      Turning OFF and then ON the power without clearing the error : Clear the error.
  • E005-0000 :
    • Fixing Cleaning Web absent error, After noticing the Fixing Cleaning Web absent, the web was pulled out 2000 times : Replace the Fixing Cleaning Web. 2. Replace the Fixing Cleaning Web Level Sensor (PS45). 3. Replace the DC Controller PCB (PCB1). After executing the measures, clear the Fixing Cleaning Web counter (COPIER > COUNTER > MISC > FIXWEB).
  • Fixing Motor error Lock error of the Fixing Motor (M3) :
    1. Check the gear of the Fixing Drive Unit : Replace the gear.
    2. Replace the Fixing Motor (M3).
    3. Check the connection drawer between the Fixing Assembly and the host machine.
    4. Replace the Main Driver PCB (PCB2).
  • ETB disengagement error, Disengagement of the ETB is not completed within the specified period of time :
    1. Check the connection of the ETB Disengage Sensor (PS56). Sensor side: J2101, J3270, PCB side: J343 (Duplex Driver PCB (PCB4))
    2. Check the connection of the Duplex Feed Left Motor (M19). Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4))
    3. Replace the ETB Disengage Sensor (PS56).
    4. Replace the Duplex Feed Left Motor (M19).
    5. Replace the Duplex Driver PCB (PCB4).
    6. Replace the DC Controller PCB (PCB1). NOTE: Check if the Disengagement Cam is stained. If necessary, clean it. Check if the drive system (gear, Motor, one-way) is failed. If necessary, replace it. Check if the link with the Fixing Feed Handle is failed. If necessary, replace it.
  • Primary Charging Shutter HP open error, The Primary Charging Shutter Sensor (PS94) detects that the shutter is opened although it is moved to the close position :
    1. Check the position of the Primary Charging Shutter and the Cleaning Pad.
    2. Check the connection of the Pre-exposure LED (connector connection, open circuit, the caught cable).
    3. Check the installation of the Primary Charging Assembly (connector connection, open circuit, the caught cable).
  • SRAM error, SRAM check error when the power is turned ON : Ckheck Main Controller PCB 2.
  • E248-0001 :Description:EEPROM error, An error when EEPROM power for the Reader Controller PCB (PCB1) is turned ON : Failure of the Reader Controller PCB (PCB1).

Power Supply Cooling Fan 1/2 error, The Fan stop signal is detected for 5 seconds or longer and retry is failed 4 times in a row although the Power Supply Cooling Fan 1 (FM14)/Power Supply Cooling Fan 2 (FM15) is turned ON. The error detection signal cable is shared with the Fans, and it is not detected with which Fan the error occurs :

  1. Check the connection of the Connector.
  2. Replace the Power Supply Cooling Fan 1 (FM14)/Power Supply Cooling Fan 2 (FM15).
  3. Replace the Fixing Power Supply Cooling Fan (FM7).
  • Fixing Power Supply error :
    1. Check the outlet voltage.
    2. Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10).
    3. Replace the Fixing Power Supply PCB (PCB10).
    4. Replace the Main Driver PCB (PCB2).
  • Fixing Shutter Motor error, The Fixing Shutter HP Sensor (PS53) failed the detection at the Fixing Shutter operation :
    1. Check the operation of the Fixing Shutter Gear (overload, etc.).
    2. Check the operation of the Fixing Shutter Motor (M15) at the initialization operation of the Fixing Shutter.
    3. Check the detection of the Fixing Shutter HP Sensor (PS53) (if the Sensor operates normally).
    4. Check the drawer of the Fixing Assembly and the host machine.
    5. Replace the Fixing Upper Unit and the Fixing Drawer Harness Unit.
    6. Replace the Main Driver PCB (PCB2) (check the fuse (FU11)).
  • Controller Fan error, Fan in the Main Controller Cooling Fan (FM4) is detected : Connector disconnection, failure of Fan and Replace Fan
  • Code E880-0005 : HDD Cooling Fan (FM) Error
Tagged

5 Comments

  1. coti usdt

    Reading your article helped me a lot and I agree with you. But I still have some doubts, can you clarify for me? I’ll keep an eye out for your answers.

  2. rtcnhmwivj

    Kode Error Canon IRAdvance | Mesin Fotocopy tidak berfungsi..sekarang Selesai

Comments are closed.